Plan your batten quantities

Roof Batten Calculator

Estimate batten rows and running length for rectangular roof planes. Enter the distance between your first and last batten, a maximum gauge and your supplier’s stock length.

✓ Rows and equal spacing ✓ Metric or imperial units ✓ Waste and purchase estimate

Enter your roof layout

Assumes straight, full-width rows on identical rectangular roof planes, with a batten at both ends of the measured distance.

Required length of each row, including any specified end allowances. All rows are assumed to have this length.
Measure along the slope between the specified first and last batten positions, using the same reference edge or centerline at both ends. This is not automatically the full eave-to-ridge slope length.
Use the permitted maximum for the selected roof covering. The default is illustrative.
Length of one purchased batten piece.
Example allowance for cutting and handling. Adjust to your planned layout.
Same stock length and suitable specification.
Quantity and geometry only. Calculated spacing must also satisfy the product’s minimum gauge and other installation requirements. Stock quantity is estimated from total running length; cutting, supported joints and offcut reuse can change the actual order. Counter-battens and special extra rows are excluded.
From spacing to running length

How to calculate roof battens

01 / SET THE END POSITIONS

Measure between the first and last rows

Establish the end batten positions from your roof covering details. Measure between them along the slope using consistent reference points.

02 / ENTER THE GAUGE

Calculate the number of spaces

Divide the measured distance by your permitted maximum gauge and round up. One additional row accounts for the batten at each end of the spaced layout.

03 / ESTIMATE MATERIAL

Convert rows into running length

Multiply rows by their length and the number of matching roof planes. Add your allowance, then divide by the supplier’s stock length to estimate full pieces.

Roof batten calculation formula

Spaces per plane
= round up(first-to-last distance ÷ maximum gauge)

Rows per plane
= spaces + 1

Calculated equal gauge
= first-to-last distance ÷ spaces

Net running length
= rows × row length × identical planes

Estimated stock pieces
= round up(length including allowance ÷ stock length)

Length and gauge are converted into compatible units before calculating. Existing matching full pieces are deducted after estimating the required stock quantity.

Example: two matching roof planes

Each plane has 10 m rows and a 5 m first-to-last distance. For an illustrative 300 mm maximum gauge:

Spaces = round up(5 ÷ 0.3) = 17
Rows per plane = 17 + 1 = 18
Equal gauge = 5 ÷ 17 ≈ 294.12 mm
Net length = 18 × 10 × 2 = 360 m
With 10% allowance = 396 m
At 3 m per stock piece = 132 pieces

The 132-piece figure is a running-length estimate. Check cutting and joint positions before ordering. Also confirm that the calculated gauge is permitted for the chosen product and roof configuration.

Understand the assumptions

Roof batten calculator questions

Why does the calculator add one to the number of spaces?

The measurement runs between the first and last batten positions. Seventeen spaces require eighteen rows because there is a batten at both ends. This convention must match the distance you enter.

Should I enter the full roof slope length?

Enter the distance between the specified first and last batten positions. Their offsets from the eave and ridge are not calculated here. The full roof slope length may therefore be different.

Does the calculated gauge confirm a compliant tile layout?

No. It produces equal spacing no greater than your entered maximum. You must also check the product’s minimum gauge, headlap, end details and other applicable requirements. The calculator does not validate those conditions.

Is the stock-piece quantity an exact cutting list?

No. It divides total length, including your allowance, by stock length. It does not allocate cuts, place joints over supports or determine which offcuts can be reused. Those constraints may increase the purchase quantity.

Can I use it for hips, valleys or unequal roof planes?

The model assumes identical rectangular planes with constant row length. Calculate unequal rectangular planes separately. Tapered rows near hips and valleys need a measured layout rather than this full-width-row estimate.

Are counter-battens or extra eave battens included?

No. Only the evenly spaced rows between your first and last positions are counted. Counter-battens, doubled rows, local reinforcement and other special details require separate quantities.

Does this choose the batten size, grade or fixing?

No. It calculates quantities from the supplied geometry. Batten section, grade, support conditions and fastening specifications must be established separately.

What does the optional material cost include?

It multiplies the estimated pieces to purchase by your price per full stock piece. It excludes fixings, labor, delivery and taxes. Currency selection labels your price without converting exchange rates.

Scroll to Top