Plan your ridge and hip coverage

Ridge Cap Calculator

Estimate ridge cap shingle bundles from the total ridge and hip length. Use your product’s installed linear coverage, add waste and deduct matching bundles already available.

✓ Ridge and hip lengths ✓ Feet or meters ✓ Bundles, stock and cost

Enter your cap requirements

For ridge and hip cap shingles sold by the bundle. Use one product and one installed coverage rate per calculation.

Add the actual lengths of all ridge runs receiving this cap product.
Measure along the sloping hip lines, not their horizontal projection. Enter 0 if none.
Use the manufacturer’s linear coverage at the specified exposure. The starting 25 ft is an example only. Do not use field-shingle area coverage.
For cuts, handling and project-specific losses. The default 10% is illustrative.
Same cap product and coverage. Do not count partial bundles as full bundles.
Use installed linear coverage. Coverage should already account for the product’s specified exposure and overlap. This calculator does not add separate starter, end or junction pieces, ridge vents or fasteners. Check those details separately.
Measure the lines, not the roof area

How to calculate ridge cap bundles

01 / MEASURE

Add ridge and hip lengths

Measure every run receiving the same cap product. Hip lengths must follow the actual sloping roof line. Roof area is not used in this calculation.

02 / CHECK COVERAGE

Read the bundle specification

Find the installed linear coverage per bundle at the specified exposure. Replace the example coverage with the figure for your chosen product.

03 / PLAN THE ORDER

Add allowance and deduct stock

Choose an allowance for your layout and handling. Round up to complete bundles, then deduct compatible full bundles already available.

Ridge cap calculation formula

Total cap length
= ridge length + hip length

Target coverage
= total cap length × (1 + allowance ÷ 100)

Required bundles
= round up(target coverage ÷ installed coverage per bundle)

Bundles to purchase
= maximum(0, required bundles − matching full bundles in stock)

Material subtotal
= bundles to purchase × price per bundle

Do not subtract overlap again when it is already reflected in the installed bundle coverage.

Example: ridges and hips together

Assume 50 ft of ridges, 80 ft of hips, an illustrative 10% allowance, and 25 ft of installed coverage per bundle.

Total length = 50 + 80 = 130 ft
Target coverage = 130 × 1.10 = 143 ft
Bundle equivalents = 143 ÷ 25 = 5.72
Required bundles = 6
With 1 matching bundle in stock, purchase 5 bundles.

Six bundles provide 150 ft of entered installed coverage. The 7 ft above the target comes from whole-bundle rounding. Special starter, end and junction details remain separate.

Before ordering cap shingles

Ridge cap calculator questions

How many bundles of ridge cap do I need?

Add the ridge and hip lengths receiving the same product, include your allowance, then divide by installed linear coverage per bundle. Round up and deduct matching full bundles already available.

Can I use the roof’s square footage?

No. Ridge cap quantity is based on linear ridge and hip lengths, not the area of the roof planes. Two roofs with the same surface area can have different cap requirements.

Does every ridge cap bundle cover the same length?

No. Use your product’s stated installed coverage at the specified exposure. The example value in this calculator is editable and is not a universal bundle specification.

Should I add overlap to the estimate?

Installed bundle coverage should already account for the product’s exposure and overlap. Do not add that same loss again. Use the extra allowance for separate cutting, handling or layout losses.

Can I combine ridge and hip lengths?

Yes, if both use the same cap product with the same installed coverage. If products or coverage rates differ, calculate them separately.

Does the result include ridge vents?

No. Ridge vent material is separate from cap shingles. The tool does not determine ventilation requirements or calculate vent accessories and fasteners.

Can this calculate metal ridge sections or ridge tiles?

This version is designed for cap shingles sold in bundles. Metal sections and ridge tiles may require per-run piece counts, end-lap calculations and dedicated end or junction components. Those details are not modeled here.

Does the estimated cost include installation?

No. It multiplies bundles to purchase by your entered price per bundle. Labor, accessories, delivery and taxes are excluded. Currency selection labels the entered price without converting exchange rates.

Scroll to Top