Plan your roof edge materials

Starter Shingle Calculator

Estimate starter shingle bundles from the eave and rake edges receiving starter. Enter your product’s installed linear coverage, add an allowance and deduct matching bundles in stock.

✓ Eaves and rake edges ✓ Feet or meters ✓ Bundles and material cost

Enter your starter requirements

Estimates one starter course along the edges entered. Use the same product and installed coverage throughout.

Add the lower roof edges included in this installation.
Measure along the sloping gable edges. Enter 0 if these edges are not included in your specified installation.
Use the manufacturer’s linear coverage for the intended starter configuration. The starting 100 ft is an example. If published coverage already includes splitting strips, do not double it again.
Allow for cuts and handling. The 10% default is illustrative; adjust for your project.
Same product and coverage. Partial bundles are not counted as full bundles.
Quantity estimate only. This tool does not determine which edges require starter or specify strip orientation, fastening or overhang. Follow the selected roofing system’s instructions. Field shingles, ridge caps and drip edge are separate materials.
Measure the edges that need starter

How to calculate starter shingles

01 / MEASURE THE EDGES

Add the relevant eaves and rakes

Enter only the edges receiving this starter product. Use actual sloping lengths for rake edges rather than their horizontal projection.

02 / CHECK THE BUNDLE

Use installed linear coverage

Find the product’s coverage for the intended starter configuration. Do not use the square-foot coverage of ordinary field-shingle bundles.

03 / ESTIMATE THE ORDER

Add allowance and deduct stock

Apply an allowance for cuts and handling, round up to complete bundles and subtract compatible full bundles you already have.

Starter shingle calculation formula

Total starter length
= included eave length + included rake length

Target coverage
= total starter length × (1 + allowance ÷ 100)

Required bundles
= round up(target coverage ÷ installed coverage per bundle)

Bundles to purchase
= maximum(0, required bundles − matching full bundles in stock)

Material subtotal
= bundles to purchase × price per bundle

The calculation assumes one starter course along the entered edges. Calculate separate products or additional specified courses separately.

Example: eaves and rakes together

Assume 100 ft of eaves, 80 ft of rakes, an illustrative 10% allowance, and 100 ft of installed coverage per bundle.

Total starter length = 100 + 80 = 180 ft
Target coverage = 180 × 1.10 = 198 ft
Bundle equivalents = 198 ÷ 100 = 1.98
Required bundles = 2
With 1 matching bundle in stock, purchase 1 bundle.

Two bundles provide 200 ft of entered installed coverage. The 2 ft above the target comes from rounding to complete bundles. Confirm your selected product’s actual coverage before ordering.

Before ordering starter materials

Starter shingle calculator questions

How many starter shingle bundles do I need?

Add the lengths of the eave and rake edges receiving starter, include your allowance, then divide by the installed coverage per bundle. Round up and deduct matching full bundles already available.

Should I include rake edges?

Include rake edges when they receive starter in your specified roofing installation. The calculator does not determine that requirement. Enter zero for rake length if those edges are outside this estimate.

Can I calculate starter bundles from roof square footage?

Starter quantity depends on the edge length receiving starter, rather than the area of the roof planes. Measure the relevant eaves and rakes for this calculation.

What if a starter sheet splits into two strips?

Use the manufacturer’s finished linear coverage for the intended configuration. If the published coverage already includes splitting the product, do not double it again. The calculator does not assume a particular split pattern.

Can I use field-shingle bundle coverage?

Not directly. Field-shingle coverage is normally expressed as roof area, while this tool needs installed starter length per bundle. It does not calculate how to cut field shingles into starter strips or determine whether that method is suitable for your roofing system.

Does this include ridge caps or drip edge?

No. Starter shingles, ridge cap shingles and metal drip edge are separate materials. Use the Ridge Cap Calculator for cap shingles and calculate drip edge independently.

How much extra starter material should I allow?

Choose an allowance based on the number of runs, cuts, corners and handling losses. The 10% default is an example. If the entered lengths already include your allowance, set the percentage here to zero.

Does the cost include installation or exchange rates?

No. It multiplies purchased bundles by your entered price. Labor, accessories, delivery and taxes are excluded. Currency selection labels the price without converting exchange rates.

Scroll to Top