Plan your roof edge trim

Drip Edge Calculator

Estimate drip edge pieces for separate roof-edge runs. Account for overlap at each joint, add spare pieces, deduct matching stock and calculate an optional material cost.

✓ Separate run calculations ✓ Joint overlap included ✓ Feet or meters

Enter your drip edge layout

Each run starts with a new full-length piece. Offcuts are not shared between runs in this estimate.

One positive number per line, up to 100 runs. Enter each straight eave or rake run separately. Use actual sloping lengths for rake edges. Use decimal points, without commas or unit symbols.
Example only. Enter the overlap specified for your installation; the tool does not determine it.
Applied to the calculated piece count and rounded up. Enter 0 for no spares. The 5% default is illustrative.
Same profile, specification and stock length.
Run-based estimate. Includes straight-run joint overlaps only. Include any specified end allowances in your entered run lengths. Corner fabrication, special fittings, fastening and offcut optimization are not modeled.
Measure every run separately

How to calculate drip edge pieces

01 / EDGE LENGTHS

List the individual runs

Enter one straight edge per line. Separating runs accounts for a new starting piece at each edge rather than treating the entire perimeter as one continuous length.

02 / PIECES AND LAPS

Enter stock length and overlap

The first piece contributes its full length. Every additional piece contributes its length minus one joint overlap. Use the overlap specified for your installation.

03 / PURCHASE QUANTITY

Add spares and deduct stock

Add an optional percentage of spare pieces. Deduct matching full pieces you already have and enter a supplier price for the material subtotal.

Drip edge calculation formula

For a run of length R, stock piece length S and overlap O, all expressed in the same unit:

If R is no longer than S:
Pieces = 1

For a longer run:
Pieces = 1 + round up((R − S) ÷ (S − O))

Coverage from N pieces:
Coverage = N × S − (N − 1) × O

Spare pieces:
Round up(total base pieces × spare percentage ÷ 100)

Overlap must be smaller than the stock piece length. The calculator counts no joint overlap for a one-piece run.

Example: four separate roof edges

Consider two 40 ft runs and two 20 ft runs, with 10 ft pieces and an illustrative 2 in overlap.

Each 40 ft run requires 5 pieces.
Each 20 ft run requires 3 pieces.
Base quantity = 5 + 5 + 3 + 3 = 16 pieces.
Spare pieces at 5% = round up(0.8) = 1.
Total required = 17 pieces.
With 2 full pieces in stock, purchase 15 pieces.

Two 10 ft pieces do not cover a 20 ft run when they overlap. This estimate starts each run with new pieces and does not reuse trimmed remnants between runs.

Understand your edge estimate

Drip edge calculator questions

Why should I enter separate edge lengths?

Each separate run has its own starting piece and rounding. Combining all edges into one length can hide the additional pieces needed at run boundaries.

Does this include overlaps?

Yes. Each joint within a straight run consumes the overlap you enter. A run using N pieces has N minus 1 joints. Corners and special junctions are not included in that count.

What overlap should I enter?

Enter the overlap specified for your chosen product and installation. The starting 2 inches is only a calculation example; the tool does not determine the required overlap.

Does the calculator reuse offcuts?

No. Every run is allocated its own full stock pieces. A planned cutting layout may allow suitable offcuts to be reused, but this calculator does not optimize that process.

Are eaves and rakes both supported?

Yes. Enter the straight eave and rake runs receiving the selected drip edge. Measure rake edges along their actual slope. Calculate different profiles or stock sizes separately.

Is the spare percentage applied to edge length?

No. It is applied to the base whole-piece count after overlaps and individual-run rounding. The resulting spare quantity is rounded up to a whole piece.

Does this specify corner cuts or fastening?

No. It estimates straight-run material quantities. Profile selection, corners, end allowances and fastening details must be determined separately.

Scroll to Top