Roof pitch explained simply: it describes how steeply a roof rises over a horizontal distance. In common roofing notation, a 6/12 pitch means the roof rises 6 inches for every 12 inches of horizontal run. That equals approximately 26.57 degrees or a 50% slope.
These numbers describe the same incline in different ways. Understanding them helps you read roofing estimates, check measurements and enter the correct values into a calculator.
This guide covers rise, run, degrees and percentage with practical examples. If you already have measurements, use the RooferTX Roof Pitch Calculator to convert them.
Roof Pitch Explained: What Do the Numbers Mean?
Roof pitch is commonly written as 4/12, 6/12 or 8/12. You may also see 6:12 or “6 in 12.”
In this notation, the first number is the vertical rise. The second is the horizontal run.
- 4/12: 4 inches of rise over 12 inches of horizontal run.
- 6/12: 6 inches of rise over 12 inches of horizontal run.
- 8/12: 8 inches of rise over 12 inches of horizontal run.
When the run stays the same, a larger rise means a steeper roof. An 8/12 roof is therefore steeper than a 4/12 roof.
The number after the slash does not describe the sloping roof length. It describes a level, horizontal distance.
Rise, Run and Span: Know the Difference
Rise is the vertical height gained between two points.
Run is the horizontal distance between those same points.
Span is the full horizontal distance across the roof between its supporting sides.
For a symmetrical gable roof with a centred ridge, the run from one supporting wall to the ridge is half the span. That shortcut does not apply to every roof shape or an off-centre ridge.
For example, a symmetrical roof with a 24-foot span has a 12-foot run on each side. If the ridge rises 6 feet above the matching wall reference level, the rise-to-run ratio is 6/12.
Are Roof Pitch and Roof Slope the Same?
In everyday roofing conversations, people often use these terms interchangeably. Traditional technical references may distinguish them:
- Pitch: total rise divided by full span.
- Slope: rise divided by horizontal run.
For a symmetrical gable roof, a traditional “quarter pitch” corresponds to a 6/12 slope—not a 3/12 slope.
Throughout this roof pitch explained guide, values such as 6/12 use the common rise-to-run convention. You can see the traditional distinction illustrated in IKO’s roof measurement guide.
How to Calculate Pitch from Rise and Run
You do not need measurements taken over exactly 12 inches. Any reliable rise and matching horizontal run can be converted into an “in 12” ratio.
Rise per 12 = (measured rise ÷ measured horizontal run) × 12
Use the same units for both measurements before dividing.
Roof Pitch Explained with a Worked Example
Suppose a roof rises 9 inches over a horizontal distance of 18 inches.
- Divide rise by run: 9 ÷ 18 = 0.5.
- Multiply by 12: 0.5 × 12 = 6.
- Write the result as 6/12.
The original measurements and the standard ratio describe exactly the same slope.
Roof Pitch Explained in Metric Units
The calculation also works with millimetres, centimetres or metres.
A roof that rises 150 mm over a 300 mm horizontal run has a rise-to-run ratio of 0.5.
(150 ÷ 300) × 12 = 6
Its equivalent is therefore 6/12.
You do not need to convert millimetres into inches first. Matching units cancel during division, leaving the same ratio.
How to Convert Roof Pitch into Degrees
The roof angle is measured upward from a horizontal line. To convert a rise-to-run ratio into degrees, use the inverse tangent function.
Angle = arctan(rise ÷ run)
For a 6/12 roof:
arctan(6 ÷ 12) = 26.57°
Set your scientific calculator to degree mode. A calculator in radian mode will display a different-looking value.
If you know the angle and want the rise per 12, reverse the calculation:
Rise per 12 = 12 × tan(angle)
For example, a 30° roof is approximately 6.93/12. Avoid rounding it to 7/12 too early when precise measurements matter.
How to Convert Roof Pitch into Percentage
Slope percentage expresses the vertical rise as a percentage of horizontal run.
Slope percentage = (rise ÷ run) × 100
For a 6/12 roof:
(6 ÷ 12) × 100 = 50%
This is where roof pitch explained in different formats can become confusing: 50% slope does not mean 50 degrees. A 50% slope is approximately 26.57°.
To convert a percentage back into an “in 12” ratio:
Rise per 12 = (slope percentage ÷ 100) × 12
A 25% slope is therefore 3/12. A 100% slope is 12/12, which equals 45°.
Roof Pitch Conversion Chart
Use this chart to compare common rise-to-run ratios. Angles and percentages are rounded to two decimal places.
| Roof pitch | Angle | Slope percentage |
|---|---|---|
| 1/12 | 4.76° | 8.33% |
| 2/12 | 9.46° | 16.67% |
| 3/12 | 14.04° | 25.00% |
| 4/12 | 18.43° | 33.33% |
| 5/12 | 22.62° | 41.67% |
| 6/12 | 26.57° | 50.00% |
| 7/12 | 30.26° | 58.33% |
| 8/12 | 33.69° | 66.67% |
| 9/12 | 36.87° | 75.00% |
| 10/12 | 39.81° | 83.33% |
| 12/12 | 45.00° | 100.00% |
Notice that doubling the rise does not double the angle. A 4/12 roof is approximately 18.43°, while an 8/12 roof is approximately 33.69°.
How Pitch Changes Roof Area
A steeper roof has more sloped surface over the same horizontal footprint. The relationship comes from the geometry of a right triangle.
Slope multiplier = √[1 + (rise ÷ run)²]
At 6/12, the multiplier is approximately 1.118034.
A horizontal roof footprint of 1,000 square feet therefore corresponds to approximately:
1,000 × 1.118034 = 1,118.03 square feet
That calculation assumes a uniform pitch and a correctly measured roof projection, including overhangs.
The increase is caused by slope. It does not include material waste.
For a complete footprint example, read how to calculate roof area. You can then check your measurements using the Roof Area Calculator.
How Pitch Affects Rafter Length
The same multiplier converts a horizontal run into its matching sloped line length.
For a 10-foot horizontal run at 6/12:
10 × 1.118034 = 11.18034 feet
This is the geometric sloped length between the corresponding endpoints. A finished rafter also involves construction details such as overhangs, ridge allowances and cuts.
Use the Rafter Length Calculator for geometric planning, then verify framing details separately before cutting.
How to Find Your Existing Roof Pitch
Start with building drawings or a reliable roof measurement report.
Check whether the recorded value is a rise-to-run ratio, percentage or angle before entering it into a calculator. A number without its measurement format can be misleading.
When measurements are taken on site, the run must be horizontal and the rise must be vertical between the corresponding points. A measurement along the sloping roof is not the run.
Record the main roof and any porch, extension or dormer separately. They may have different slopes.
A ground-level photograph can help illustrate a roof, but perspective makes it unreliable for an exact angle measurement. Use a qualified professional when obtaining measurements would require unsafe roof or attic access.
Common Mistakes When Reading Roof Pitch
With roof pitch explained in several formats, it becomes easier to spot mistakes before they affect your estimate.
Reading 6/12 as 6°.
The first number is rise per 12 units of horizontal run, not degrees.
Confusing percentage with angle.
A 50% slope is approximately 26.57°, not 50°.
Using full span as the run.
On a symmetrical gable roof, one side’s run is half the span.
Mixing measurement units.
Convert feet and inches into matching units before dividing. For example, 6 inches of rise over 1 foot of run means 6 ÷ 12, not 6 ÷ 1.
Measuring along the slope.
Run is horizontal distance, not rafter length.
Assuming one pitch applies everywhere.
Check additions and secondary roof planes individually.
Use Your Pitch Measurement for Better Planning
Understanding the ratio, angle and percentage helps you compare roof measurements without confusing one format with another.
For material selection, check the specific product’s slope requirements. Pitch alone does not confirm that a roof covering or installation method is suitable.
Start with the RooferTX pitch conversion tool, then use the result alongside your roof dimensions to calculate surface area and plan material quantities.
Frequently Asked Questions
What Does a 6/12 Roof Pitch Mean?
A 6/12 pitch means 6 units of vertical rise for every 12 units of horizontal run. It equals a 50% slope and an angle of approximately 26.57°.
Is a 4/12 Roof Steeper Than a 6/12 Roof?
No. A 6/12 roof rises farther over the same horizontal distance. Its angle is approximately 26.57°, compared with 18.43° for a 4/12 roof.
What Roof Pitch Is 30 Degrees?
A 30° angle equals approximately 6.93/12. Calculate it by multiplying the tangent of 30° by 12.
Does a 100% Slope Mean a Vertical Roof?
No. A 100% slope means the rise equals the horizontal run. That produces a 45° angle, equivalent to 12/12.
Can Roof Pitch Be Greater Than 12/12?
Yes. A pitch greater than 12/12 is steeper than 45°. For example, 18/12 corresponds to approximately 56.31°.
Can One Roof Have Several Different Pitches?
Yes. Main roof planes, porches, dormers and extensions can have different slopes. Record and calculate them separately when estimating roof area.
Can I Find Pitch from Rafter Length Alone?
No. A sloped length alone does not identify the roof angle. You also need another measurement, such as the corresponding horizontal run or vertical rise.

Your worked example of 9 inches of rise over 18 inches of run reducing to a 6/12 pitch, plus the warning not to confuse a 50% slope with 50 degrees (it is 26.57 degrees), clears up the two mistakes I see homeowners make most often. Once the ratio is nailed down, running it through a roof pitch calculator to flip between rise-over-run, degrees, and percentage saves a lot of head-scratching when ordering materials. Really solid reference guide, thanks for writing it.